The MIB module defining objects for the management of a pair of
ADSL modems at each end of the ADSL line.  Each such line has


an entry in an ifTable which may include multiple modem lines.
An agent may reside at either end of the ADSL line however the
MIB is designed to require no management communication between
them beyond that inherent in the low-level ADSL line protocol.
The agent may monitor and control this protocol for its needs.

ADSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus an ADSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to adsl(94), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.

Naming Conventions:
Atuc -- (ATUC) modem at near (Central) end of line
Atur -- (ATUR) modem at Remote end of line
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES  -- Errored Second.
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xxxs-- interval of Seconds in which xxx occurs
(e.g., xxx=Lof, Los, Lpr)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx  -- Transmit
Blks-- Blocks, a data unit, see
adslAtuXChanCrcBlockLength

This table includes common attributes describing
both ends of the line.  It is required for all ADSL
physical interfaces.  ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).    

Specifies the ADSL coding type used on this
line.    

Possible values are:


noChannel, fastOnly, interleavedOnly, 
fastOrInterleaved, fastAndInterleaved

Defines the type of ADSL physical line
entity that exists, by defining whether and how
the line is channelized.  If the line is channelized,
the value will be other than noChannel(1).  This
object defines which channel type(s) are supported.

In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s).    

OID instance in vendor-specific MIB. The Instance may
be used to determine shelf/slot/port of the ATUC
interface in a DSLAM.    

The value of this object identifies the row
in the ADSL Line Configuration Profile Table,
(adslLineConfProfileTable), which applies for this
ADSL line, and channels if applicable.

For `dynamic' mode, in the case which the
configuration profile has not been set, the
value will be set to `DEFVAL'.

If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only.    

The value of this object identifies the row
in the ADSL Line Alarm Configuration Profile Table,
(adslLineAlarmConfProfileTable), which applies to this
ADSL line, and channels if applicable.

For `dynamic' mode, in the case which the
alarm profile has not been set, the
value will be set to `DEFVAL'.

If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only.    

This table provides one row for each ATUC channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Count of all encoded blocks received on this channel
since agent reset.    

Count of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.    

Count of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.    

Number of seconds that have elapsed since the
beginning of the current 1-day interval.    

Count of all encoded blocks received on this
channel during the current day as measured by

adslAtucChanPerfCurr1DayTimeElapsed.    

Count of all encoded blocks transmitted on this
channel during the current day as measured by
adslAtucChanPerfCurr1DayTimeElapsed.    

Count of all blocks received with errors that were
corrected on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.    

Count of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adslAtucChanPerfCurr1DayTimeElapsed.    

The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason.    

Count of all encoded blocks received on this
channel within the most recent previous 1-day
period.    

Count of all encoded blocks transmitted on this
channel within the most recent previous 1-day
period.    

Count of all encoded blocks transmitted on this
channel since agent reset.    

Count of all blocks received with errors that were
corrected on this channel within the most recent
previous 1-day period.    

Count of all blocks received with uncorrectable
errors on this channel within the most recent previous
1-day period.    

Count of all blocks received with errors that were
corrected since agent reset.  These blocks are passed
on as good data.    

Count of all blocks received with uncorrectable
errors since agent reset.    

The number of previous 15-minute intervals in the
interval table for which data was collected.  Given
that  is the maximum # of intervals supported.
The value will be  unless the measurement was
(re-)started within the last (*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable.  In this case, this
interval is the maximum interval number for
which data is available.    

The number of intervals in the range from
0 to the value of adslAtucChanPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations).    

Count of all encoded blocks received on this channel
within the current 15 minute interval.    

Count of all encoded blocks transmitted on this
channel within the current 15 minute interval.    

This table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Count of all encoded blocks received on this channel
since agent reset.    

Count of all blocks received with errors that were
corrected on this channel within the current 15 minute
interval.    

Count of all blocks received with uncorrectable
errors on this channel within the current 15 minute
interval.    

Number of seconds that have elapsed since the
beginning of the current 1-day interval.    

Count of all encoded blocks received on this
channel during the current day as measured by
adslAturChanPerfCurr1DayTimeElapsed.    

Count of all encoded blocks transmitted on this
channel during the current day as measured by
adslAturChanPerfCurr1DayTimeElapsed.    

Count of all blocks received with errors that were
corrected on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.    

Count of all blocks received with uncorrectable
errors on this channel during the current day as
measured by adslAturChanPerfCurr1DayTimeElapsed.    

The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason.    

Count of all encoded blocks received on this
channel within the most recent previous 1-day
period.    

Count of all encoded blocks transmitted on this
channel within the most recent previous 1-day
period.    

Count of all encoded blocks transmitted on this
channel since agent reset.    

Count of all blocks received with errors that were
corrected on this channel within the most recent
previous 1-day period.    

Count of all blocks received with uncorrectable
errors on this channel within the most recent previous
1-day period.    

Count of all blocks received with errors that were
corrected since agent reset.  These blocks are passed
on as good data.    

Count of all blocks received with uncorrectable
errors since agent reset.    

The number of previous 15-minute intervals in the
interval table for which data was collected.  Given
that  is the maximum # of intervals supported.
The value will be  unless the measurement was
(re-)started within the last (*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable.  In this case, this
interval is the maximum interval number for
which data is available.    

The number of intervals in the range from
0 to the value of adslAturChanPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations).    

Total elapsed seconds in this interval.
A full interval is 900 seconds.    

Count of all encoded blocks received on this
channel within the current 15 minute interval.    

Count of all encoded blocks transmitted on this
channel within the current 15 minute interval.    

This table provides one row for each ATUC channel's
performance data collection interval.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago.  Intervals 2..96 are
optional.    

Count of all encoded blocks received on this channel
during this interval.    

Count of all encoded blocks transmitted on this
channel during this interval.    

Count of all blocks received with errors that were
corrected on this channel during this interval.    

Count of all blocks received with uncorrectable
errors on this channel during this interval.    

This variable indicates if the data for this
interval is valid.    

This table provides one row for each ATUR channel's
performance data collection interval.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago.  Intervals 2..96 are
optional.    

Count of all encoded blocks received on this channel
during this interval.    

Count of all encoded blocks transmitted on this
channel during this interval.    

Count of all blocks received with errors that were
corrected on this channel during this interval.    

Count of all blocks received with uncorrectable
errors on this channel during this interval.    

This variable indicates if the data for this
interval is valid.    

This table contains information on the ADSL line
configuration.  One entry in this table reflects a
profile defined by a manager which can be used to
configure the ADSL line.    

Each entry consists of a list of parameters that
represents the configuration of an ADSL modem.

When `dynamic' profiles are implemented, a default
profile will always exist.  This profile's name will
be set to `DEFVAL' and its parameters will be set
to vendor specific values, unless otherwise specified
in this document.

When `static' profiles are implemented, profiles
are automaticly created or destroyed as ADSL
physical lines are discovered and removed by
the system.  The name of the profile will be
equivalent to the decimal value of the line's
interface index.

This object is used by the line configuration table
in order to identify a row of this table.

When `dynamic' profiles are implemented, the profile
name is user specified.  Also, the system will always
provide a default profile whose name is `DEFVAL'.

When `static' profiles are implemented, there is an
one-to-one relationship between each line and its
profile.  In which case, the profile name will
need to algorithmicly represent the Line's ifIndex.
Therefore, the profile's name is a decimalized string
of the ifIndex that is fixed-length (i.e., 10) with
leading zero(s).  For example, the profile name for
ifIndex which equals '15' will be '0000000015'.    

Minimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs.
In the case that RADSL mode is not present,
the value will be `0'.    

Configured Minimum Transmit rate for `Fast' channels,
in bps.  See adslAtucConfRateChanRatio for information
regarding RADSL mode and ATUR transmit rate for
ATUC receive rates.    

Configured Minimum Transmit rate for `Interleave'
channels, in bps.  See adslAtucConfRateChanRatio for
information regarding RADSL mode and see
ATUR transmit rate for receive rates.    

Configured Maximum Transmit rate for `Fast' channels,
in bps.  See adslAtucConfRateChanRatio for information
regarding RADSL mode and see ATUR transmit rate for
ATUC receive rates.    

Configured Maximum Transmit rate for `Interleave'
channels, in bps.  See adslAtucConfRateChanRatio for
information regarding RADSL mode and ATUR transmit
rate for ATUC receive rates.    

Configured maximum Interleave Delay for this channel.

Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output.  Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.    

Possible values are:


fixed, adaptAtStartup, adaptAtRuntime
                

Defines what form of transmit rate adaptation is
configured on this modem.  See ADSL Forum TR-005 [3]
for more information.    

Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels.  Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAturConfRateChanRatio =

[Fast / (Fast + Interleaved)] * 100

In other words this value is the fast channel
percentage.    

Configured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.    

Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.    

Possible values are:


fixed, adaptAtStartup, adaptAtRuntime
                

Defines what form of transmit rate adaptation is
configured on this modem.  See ADSL Forum TR-005 [3]
for more information.    

Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output.  If that
is not possible the modem will attempt to
re-initialize or shut down.    

Configured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate.
In the case that RADSL mode is not present,
the value will be `0'.    

Configured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate.
In the case that RADSL is not present,
the value will be `0'.    

Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs.
In the case that RADSL is not present, the value will
be `0'.    

Minimum time that the current margin is below
DownshiftSnrMgn before a downshift occurs.
In the case that RADSL mode is not present,
the value will be `0'.    

Configured Minimum Transmit rate for `Fast' channels,
in bps.  See adslAturConfRateChanRatio for information
regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.    

Configured Minimum Transmit rate for `Interleave'
channels, in bps.  See adslAturConfRateChanRatio for
information regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.    

Configured Maximum Transmit rate for `Fast' channels,
in bps.  See adslAturConfRateChanRatio for information
regarding RADSL mode and ATUC transmit rate
for ATUR receive rates.    

Configured Maximum Transmit rate for `Interleave'
channels, in bps.  See adslAturConfRateChanRatio for
information regarding RADSL mode and see
ATUC transmit rate for ATUR receive rates.    

Configured maximum Interleave Delay for this channel.

Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output.  Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.    

Configured allocation ratio of excess transmit
bandwidth between fast and interleaved channels.  Only
applies when two channel mode and RADSL are supported.
Distribute bandwidth on each channel in excess of the
corresponding ChanConfMinTxRate so that:
adslAtucConfRateChanRatio =

[Fast / (Fast + Interleaved)] * 100

In other words this value is the fast channel
percentage.    

This object is used to create a new row or modify or
delete an existing row in this table.

A profile activated by setting this object to
`active'.  When `active' is set, the system
will validate the profile.

Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.

If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only and its value
is always to be `active'.    

Configured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.    

Configured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.    

Configured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output.  If that
is not possible the modem will attempt to
re-initialize or shut down.    

Configured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate.  In
the case that RADSL mode is not present,
the value will be `0'.    

Configured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate.    In
the case that RADSL is not present, the value will

be `0'.    

Minimum time that the current margin is above
UpshiftSnrMgn before an upshift occurs.
In the case that RADSL is not present, the value will
be `0'.    

This table contains information on the ADSL line
configuration.  One entry in this table reflects a
profile defined by a manager which can be used to
configure the modem for a physical line    

Each entry consists of a list of parameters that
represents the configuration of an ADSL modem.

When `dynamic' profiles are implemented, a default
profile will always exist.  This profile's name will
be set to `DEFVAL' and its parameters will be set to
vendor specific values, unless otherwise specified
in this document.

When `static' profiles are implemented, profiles
are automaticly created or destroyed as ADSL
physical lines are discovered and removed by
the system.  The name of the profile will be
equivalent to the decimal value of the line's
interface index.

This object is used by the line alarm configuration
table in order to identify a row of this table.

When `dynamic' profiles are implemented, the profile
name is user specified.  Also, the system will always
provide a default profile whose name is `DEFVAL'.

When `static' profiles are implemented, there is an
one-to-one relationship between each line and its
profile.  In which case, the profile name will
need to algorithmicly represent the Line's ifIndex.
Therefore, the profile's name is a decimalized string
of the ifIndex that is fixed-length (i.e., 10) with
leading zero(s).  For example, the profile name for
ifIndex which equals '15' will be '0000000015'.    

Applies to `Interleave' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap.  A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. A value of `0' will disable the trap.    

Possible values are:


enable, disable
                

Enables and disables the InitFailureTrap.  This
object is defaulted disable(2).    

The number of Loss of Frame Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAturPerfLofsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Loss of Signal Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAturPerfLossThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Loss of Power Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAturPerfLprsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Errored Seconds

encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAturPerfESsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

Applies to `Fast' channels only.
Configured change in rate causing an
adslAturRateChangeTrap.  A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.    

Applies to `Interleave' channels only.
configured change in rate causing an
adslAturRateChangeTrap.  A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.    

Applies to `Fast' channels only.
Configured change in rate causing an
adslAturRateChangeTrap.  A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. A value of `0' will disable the trap.    

Applies to `Interleave' channels only.
Configured change in rate causing an
adslAturRateChangeTrap.  A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. A value of `0' will disable the trap.    

The number of Loss of Frame Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLofsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

This object is used to create a new row or modify or
delete an existing row in this table.

A profile activated by setting this object to
`active'.  When `active' is set, the system
will validate the profile.

Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.

If the implementator of this MIB has chosen not
to implement `dynamic assignment' of profiles, this
object's MIN-ACCESS is read-only and its value
is always to be `active'.    

The number of Loss of Signal Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLossThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Loss of Link Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLolsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Loss of Power Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfLprsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

The number of Errored Seconds
encountered by an ADSL interface within any given 15
minutes performance data collection period, which
causes the SNMP agent to send an
adslAtucPerfESsThreshTrap.
One trap will be sent per interval per interface.
A value of `0' will disable the trap.    

Applies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap. A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.    

Applies to `Interleave' channels only.
Configured change in rate causing an

adslAtucRateChangeTrap.  A trap is produced when:
ChanCurrTxRate >= ChanPrevTxRate plus the value of
this object. A value of `0' will disable the trap.    

Applies to `Fast' channels only.
Configured change in rate causing an
adslAtucRateChangeTrap.  A trap is produced when:
ChanCurrTxRate <= ChanPrevTxRate minus the value of
this object. A value of `0' will disable the trap.    

This table provides one row for each ATUC.
Each row contains the Physical Layer Parameters
table for that ATUC. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).    

The vendor specific string that identifies the
vendor equipment.    

The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters.    

The vendor specific version number sent by this ATU
as part of the initialization messages.  It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters.    

Noise Margin as seen by this ATU with respect to its
received signal in tenth dB.    

Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.    

Indicates current state of the ATUC line.  This is a
bit-map of possible conditions.  The various bit
positions are:

0      noDefect             There no defects on the line

1      lossOfFraming        ATUC failure due to not
receiving valid frame.

2      lossOfSignal         ATUC failure due to not
receiving signal.

3      lossOfPower          ATUC failure due to loss of
power.
Note: the Agent may still
function.

4      lossOfSignalQuality  Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise

Margin, or the bit-error-rate
exceeds 10^-7.

5      lossOfLink           ATUC failure due to inability
to link with ATUR.

6      dataInitFailure      ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.

7      configInitFailure    ATUC failure during
initialization due to peer
ATU not able to support
requested configuration

8      protocolInitFailure  ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.

9      noPeerAtuPresent     ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.

This is intended to supplement ifOperStatus.    

Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.    

Indicates the maximum currently attainable data rate
by the ATU.  This value will be equal or greater than

the current line rate.    

This table provides one row for each ATUR
Each row contains the Physical Layer Parameters
table for that ATUR. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).    

The vendor specific string that identifies the
vendor equipment.    

The vendor ID code is a copy of the binary
vendor identification field defined by the
PHY[10] and expressed as readable characters.    

The vendor specific version number sent by this ATU
as part of the initialization messages.  It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters.    

Noise Margin as seen by this ATU with respect to its
received signal in tenth dB.    

Measured difference in the total power transmitted by
the peer ATU and the total power received by this ATU.    

Indicates current state of the ATUR line.  This is a
bit-map of possible conditions.  Due to the isolation
of the ATUR when line problems occur, many state
conditions like loss of power, loss of quality signal,
and initialization errors,  can not be determined.
While trouble shooting ATUR, also use object,
adslAtucCurrStatus.  The various bit positions are:

0      noDefect             There no defects on the line

1      lossOfFraming        ATUR failure due to not
receiving valid frame

2      lossOfSignal         ATUR failure due to not
receiving signal

3      lossOfPower          ATUR failure due to loss of
power

4      lossOfSignalQuality  Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the
bit-error-rate exceeds 10^-7.

This is intended to supplement ifOperStatus.    

Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.    

Indicates the maximum currently attainable data rate
by the ATU.  This value will be equal or greater than
the current line rate.    

This table provides one row for each ATUC channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Interleave Delay for this channel.

Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement

in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.

In the case where the ifType is Fast(125), use
noSuchObject.    

The rate at the time of the last
adslAtucRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.

Rate changes less than adslAtucThresh(*)RateDown
or less than adslAtucThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry.    

Indicates the length of the channel data-block
on which the CRC operates.  Refer to Line Code
Specific MIBs, [11] and [12] for more
information.    

This table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).    

Interleave Delay for this channel.

Interleave delay applies only to the
interleave channel and defines the mapping
(relative spacing) between subsequent input
bytes at the interleaver input and their placement
in the bit stream at the interleaver output.
Larger numbers provide greater separation between
consecutive input bytes in the output bit stream
allowing for improved impulse noise immunity at
the expense of payload latency.

In the case where the ifType is Fast(125), use

noSuchObject.    

The rate at the time of the last
adslAturRateChangeTrap event. It is also set at
initialization to prevent a trap being sent.
Rate changes less than adslAturThresh(*)RateDown
or less than adslAturThresh(*)RateUp will not
cause a trap or cause this object to change.
(*) == Fast or Interleave.
See AdslLineAlarmConfProfileEntry.    

Indicates the length of the channel data-block
on which the CRC operates.  Refer to Line Code
Specific MIBs, [11] and [12] for more
information.    

This table provides one row for each ATUC.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).    

Count of the number of Loss of Framing failures since
agent reset.    

Count of seconds in the current 15 minute interval
when there was Loss of Framing.    

Count of seconds in the current 15 minute interval
when there was Loss of Signal.    

Count of seconds in the current 15 minute interval
when there was Loss of Link.    

Count of seconds in the current 15 minute interval
when there was Loss of Power.    

Count of Errored Seconds in the current 15 minute
interval.  The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

Count of the line initialization attempts in the
current 15 minute interval. Includes both successful
and failed attempts.    

Number of seconds that have elapsed since the
beginning of the current 1-day interval.    

Count of the number of seconds when there was Loss of
Framing during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.    

Count of the number of seconds when there was Loss of
Signal during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.    

Count of the number of seconds when there was Loss of
Link during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.    

Count of the number of Loss of Signal failures since
agent reset.    

Count of the number of seconds when there was Loss of
Power during the current day as measured by
adslAtucPerfCurr1DayTimeElapsed.    

Count of Errored Seconds during the current day as
measured by adslAtucPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

Count of the line initialization attempts in the
day as measured by adslAtucPerfCurr1DayTimeElapsed.
Includes both successful and failed attempts.    

The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason.    

Count of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period.    

Count of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period.    

Count of seconds in the interval when there was
Loss of Link within the most recent previous
1-day period.    

Count of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period.    

Count of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects.    

Count of the line initialization attempts in the most
recent previous 1-day period. Includes both successful
and failed attempts.    

Count of the number of Loss of Link failures since
agent reset.    

Count of the number of Loss of Power failures since
agent reset.    

Count of the number of Errored Seconds since agent
reset.  The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

Count of the line initialization attempts since
agent reset. Includes both successful and failed
attempts.    

The number of previous 15-minute intervals in the
interval table for which data was collected.  Given
that  is the maximum # of intervals supported.
The value will be  unless the measurement was
(re-)started within the last (*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable.  In this case, this
interval is the maximum interval number for
which data is available.    

The number of intervals in the range from
0 to the value of adslAtucPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations).    

This table provides one row for each ATUR.
ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).    

Count of the number of Loss of Framing failures since
agent reset.    

Count of seconds in the current 15 minute interval
when there was Loss of Power.    

Count of Errored Seconds in the current 15 minute
interval.  The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

Number of seconds that have elapsed since the
beginning of the current 1-day interval.    

Count of the number of seconds when there was Loss
of Framing during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.    

Count of the number of seconds when there was Loss
of Signal during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.    

Count of the number of seconds when there was Loss
of Power during the current day as measured by
adslAturPerfCurr1DayTimeElapsed.    

Count of Errored Seconds during the current day as
measured by adslAturPerfCurr1DayTimeElapsed.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

The amount of time in the previous 1-day interval
over which the performance monitoring information
is actually counted. This value will be the same as
the interval duration except in a situation where
performance monitoring data could not be collected
for any reason.    

Count of seconds in the interval when there was
Loss of Framing within the most recent previous
1-day period.    

Count of seconds in the interval when there was
Loss of Signal within the most recent previous
1-day period.    

Count of the number of Loss of Signal failures since
agent reset.    

Count of seconds in the interval when there was
Loss of Power within the most recent previous
1-day period.    

Count of Errored Seconds within the most recent
previous 1-day period. The errored second parameter is
a count of one-second intervals containing one or more
crc anomalies, or one or more los or sef defects.    

Count of the number of Loss of Power failures since
agent reset.    

Count of the number of Errored Seconds since agent
reset.  The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

The number of previous 15-minute intervals in the
interval table for which data was collected.  Given
that  is the maximum # of intervals supported.
The value will be  unless the measurement was
(re-)started within the last (*15) minutes, in which
case the value will be the number of complete 15
minute intervals for which the agent has at least
some data. In certain cases (e.g., in the case
where the agent is a proxy) it is possible that some
intervals are unavailable.  In this case, this
interval is the maximum interval number for
which data is available.    

The number of intervals in the range from
0 to the value of adslAturPerfValidIntervals
for which no data is available. This object
will typically be zero except in cases where
the data for some intervals are not available
(e.g., in proxy situations).    

Count of seconds in the current 15 minute interval
when there was Loss of Framing.    

Count of seconds in the current 15 minute interval
when there was Loss of Signal.    

This table provides one row for each ATUC
performance data collection interval.
ADSL physical interfaces are

those ifEntries where ifType is equal to adsl(94).    

Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago.  Intervals 2..96 are
optional.    

Count of seconds in the interval when there was Loss
of Framing.    

Count of seconds in the interval when there was Loss
of Signal.    

Count of seconds in the interval when there was Loss
of Link.    

Count of seconds in the interval when there was Loss
of Power.    

Count of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

Count of the line initialization attempts
during the interval. Includes both successful
and failed attempts.    

This variable indicates if the data for this
interval is valid.    

This table provides one row for each ATUR
performance data collection interval.
ADSL physical interfaces are those
ifEntries where ifType is equal to adsl(94).    

Performance Data Interval number 1 is the
the most recent previous interval; interval
96 is 24 hours ago.  Intervals 2..96 are
optional.    

Count of seconds in the interval when there was
Loss of Framing.    

Count of seconds in the interval when there was
Loss of Signal.    

Count of seconds in the interval when there was
Loss of Power.    

Count of Errored Seconds in the interval.
The errored second parameter is a count of
one-second intervals containing one or more crc
anomalies, or one or more los or sef defects.    

This variable indicates if the data for this

interval is valid.    

Values are:


adslAtucPerfCurr15MinLofs, 
adslAtucThresh15MinLofs

Loss of Framing 15-minute interval threshold reached.    

Values are:


adslAtucPerfCurr15MinLoss, 
adslAtucThresh15MinLoss

Loss of Signal 15-minute interval threshold reached.    

Values are:


adslAtucPerfCurr15MinLprs, 
adslAtucThresh15MinLprs

Loss of Power 15-minute interval threshold reached.    

Values are:


adslAtucPerfCurr15MinESs, 
adslAtucThresh15MinESs

Errored Second 15-minute interval threshold reached.    

Values are:


adslAtucChanCurrTxRate, 
adslAtucChanPrevTxRate
                

The ATUCs transmit rate has changed (RADSL mode only)    

Values are:


adslAtucPerfCurr15MinLols, 
adslAtucThresh15MinLols

Loss of Link 15-minute interval threshold reached.    

Values are:


adslAtucCurrStatus
                

ATUC initialization failed. See adslAtucCurrStatus
for potential reasons.    

Values are:


adslAturPerfCurr15MinLofs, 
adslAturThresh15MinLofs

Loss of Framing 15-minute interval threshold reached.    

Values are:


adslAturPerfCurr15MinLoss, 
adslAturThresh15MinLoss

Loss of Signal 15-minute interval threshold reached.    

Values are:


adslAturPerfCurr15MinLprs, 
adslAturThresh15MinLprs

Loss of Power 15-minute interval threshold reached.    

Values are:


adslAturPerfCurr15MinESs, 
adslAturThresh15MinESs

Errored Second 15-minute interval threshold reached.    

Values are:


adslAturChanCurrTxRate, 
adslAturChanPrevTxRate
                

The ATURs transmit rate has changed (RADSL mode only)    

Values are:


adslLineCoding, adslLineType, 
adslLineSpecific
                

A collection of objects providing configuration
information about an ADSL Line.    

Values are:


adslAtucConfRateMode, 
adslAtucConfRateChanRatio, 
adslAtucConfTargetSnrMgn, 
adslAtucConfMaxSnrMgn, 
adslAtucConfMinSnrMgn, 
adslAtucConfDownshiftSnrMgn, 
adslAtucConfUpshiftSnrMgn, 
adslAtucConfMinUpshiftTime, 
adslAtucConfMinDownshiftTime, 
adslAtucChanConfFastMinTxRate, 
adslAtucChanConfInterleaveMinTxRate, 
adslAtucChanConfFastMaxTxRate, 
adslAtucChanConfInterleaveMaxTxRate, 
adslAtucChanConfMaxInterleaveDelay, 
adslAturConfRateMode, 
adslAturConfRateChanRatio, 
adslAturConfTargetSnrMgn, 
adslAturConfMaxSnrMgn, 
adslAturConfMinSnrMgn, 
adslAturConfDownshiftSnrMgn, 
adslAturConfUpshiftSnrMgn, 
adslAturConfMinUpshiftTime, 
adslAturConfMinDownshiftTime, 
adslAturChanConfFastMinTxRate, 
adslAturChanConfInterleaveMinTxRate, 
adslAturChanConfFastMaxTxRate, 
adslAturChanConfInterleaveMaxTxRate, 
adslAturChanConfMaxInterleaveDelay

A collection of objects providing provisioning
information about an ADSL Line.    

Values are:


adslAtucThresh15MinLofs, 
adslAtucThresh15MinLoss, 
adslAtucThresh15MinLols, 
adslAtucThresh15MinLprs, 
adslAtucThresh15MinESs, 
adslAtucThreshFastRateUp, 
adslAtucThreshInterleaveRateUp, 
adslAtucThreshFastRateDown, 
adslAtucThreshInterleaveRateDown, 
adslAtucInitFailureTrapEnable, 
adslAturThresh15MinLofs, 
adslAturThresh15MinLoss, 
adslAturThresh15MinLprs, 
adslAturThresh15MinESs, 
adslAturThreshFastRateUp, 
adslAturThreshInterleaveRateUp, 
adslAturThreshFastRateDown, 
adslAturThreshInterleaveRateDown

A collection of objects providing alarm provisioning
information about an ADSL Line.    

Values are:


adslLineConfProfile, 
adslLineAlarmConfProfile, 
adslLineConfProfileRowStatus, 
adslLineAlarmConfProfileRowStatus

A collection of objects providing profile
control for the ADSL system.    

Values are:


adslAtucPerfLofsThreshTrap, 
adslAtucPerfLossThreshTrap, 
adslAtucPerfLprsThreshTrap, 
adslAtucPerfESsThreshTrap, 
adslAtucRateChangeTrap, 
adslAtucPerfLolsThreshTrap, 
adslAtucInitFailureTrap, 
adslAturPerfLofsThreshTrap, 
adslAturPerfLossThreshTrap, 
adslAturPerfLprsThreshTrap, 
adslAturPerfESsThreshTrap, 
adslAturRateChangeTrap

Values are:


adslLineCoding
                

A collection of objects providing configuration
information about an ADSL Line on the ATU-R side.    

Values are:


adslAtucInvVendorID, 
adslAtucInvVersionNumber, 
adslAtucCurrOutputPwr, 
adslAtucCurrAttainableRate, 
adslAturInvSerialNumber, 
adslAturInvVendorID, 
adslAturInvVersionNumber, 
adslAturCurrSnrMgn, adslAturCurrAtn, 
adslAturCurrStatus, 
adslAturCurrOutputPwr, 
adslAturCurrAttainableRate, 
adslAtucCurrStatus

A collection of objects providing physical
configuration information of the ADSL Line on the
ATU-R side.    

Values are:


adslAtucChanInterleaveDelay, 
adslAtucChanCurrTxRate, 
adslAtucChanPrevTxRate, 
adslAturChanInterleaveDelay, 
adslAturChanCurrTxRate, 
adslAturChanPrevTxRate, 
adslAturChanCrcBlockLength

A collection of objects providing configuration
information about an ADSL channel on the ATU-R
side.    

Values are:


adslAtucPerfLofs, adslAtucPerfLoss, 
adslAtucPerfESs, adslAtucPerfInits

A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end) provided by the
ATU-R agent.    

Values are:


adslAtucPerfValidIntervals, 
adslAtucPerfInvalidIntervals, 
adslAtucPerfCurr15MinTimeElapsed, 
adslAtucPerfCurr15MinLofs, 
adslAtucPerfCurr15MinLoss, 
adslAtucPerfCurr15MinESs, 
adslAtucPerfCurr15MinInits, 
adslAtucPerfCurr1DayTimeElapsed, 
adslAtucPerfCurr1DayLofs, 
adslAtucPerfCurr1DayLoss, 
adslAtucPerfCurr1DayESs, 
adslAtucPerfCurr1DayInits, 
adslAtucPerfPrev1DayMoniSecs, 
adslAtucPerfPrev1DayLofs, 
adslAtucPerfPrev1DayLoss, 
adslAtucPerfPrev1DayESs, 
adslAtucPerfPrev1DayInits, 
adslAtucIntervalLofs, 
adslAtucIntervalLoss, 
adslAtucIntervalESs, 
adslAtucIntervalInits, 
adslAtucIntervalValidData

A collection of objects providing current

15-minute, 1-day; and previous 1-day performance
counts on ADSL Line (ATU-C end) provided by the
ATU-R agent.    

Values are:


adslAturPerfLofs, adslAturPerfLoss, 
adslAturPerfLprs, adslAturPerfESs

A collection of objects providing raw performance
counts on an ADSL Line (ATU-R end) provided by the
ATU-R agent.    

Values are:


adslAtucInvSerialNumber, 
adslAtucInvVendorID, 
adslAtucInvVersionNumber, 
adslAtucCurrSnrMgn, adslAtucCurrAtn, 
adslAtucCurrStatus, 
adslAtucCurrOutputPwr, 
adslAtucCurrAttainableRate, 
adslAturInvSerialNumber, 
adslAturInvVendorID, 
adslAturInvVersionNumber, 
adslAturCurrSnrMgn, adslAturCurrAtn, 
adslAturCurrStatus, 
adslAturCurrOutputPwr, 
adslAturCurrAttainableRate

A collection of objects providing physical
configuration information of the ADSL Line.    

Values are:


adslAturPerfValidIntervals, 
adslAturPerfInvalidIntervals, 
adslAturPerfCurr15MinTimeElapsed, 
adslAturPerfCurr15MinLofs, 
adslAturPerfCurr15MinLoss, 
adslAturPerfCurr15MinLprs, 
adslAturPerfCurr15MinESs, 
adslAturPerfCurr1DayTimeElapsed, 
adslAturPerfCurr1DayLofs, 
adslAturPerfCurr1DayLoss, 
adslAturPerfCurr1DayLprs, 
adslAturPerfCurr1DayESs, 
adslAturPerfPrev1DayMoniSecs, 
adslAturPerfPrev1DayLofs, 
adslAturPerfPrev1DayLoss, 
adslAturPerfPrev1DayLprs, 
adslAturPerfPrev1DayESs, 
adslAturIntervalLofs, 
adslAturIntervalLoss, 
adslAturIntervalLprs, 
adslAturIntervalESs, 
adslAturIntervalValidData

A collection of objects providing current
15-minute, 1-day; and previous 1-day performance
counts on ADSL Line (ATU-R end) provided by the
ATU-R agent.    

Values are:


adslAtucChanReceivedBlks, 
adslAtucChanTransmittedBlks, 
adslAtucChanCorrectedBlks, 
adslAtucChanUncorrectBlks, 
adslAtucChanPerfCurr15MinTimeElapsed, 
adslAtucChanPerfCurr15MinReceivedBlks, 
adslAtucChanPerfCurr15MinTransmittedBlks, 
adslAtucChanPerfCurr15MinCorrectedBlks, 
adslAtucChanPerfCurr15MinUncorrectBlks, 
adslAtucChanPerfCurr1DayTimeElapsed, 
adslAtucChanPerfCurr1DayReceivedBlks, 
adslAtucChanPerfCurr1DayTransmittedBlks, 
adslAtucChanPerfCurr1DayCorrectedBlks, 
adslAtucChanPerfCurr1DayUncorrectBlks, 
adslAtucChanPerfPrev1DayMoniSecs, 
adslAtucChanPerfPrev1DayReceivedBlks, 
adslAtucChanPerfPrev1DayTransmittedBlks, 
adslAtucChanPerfPrev1DayCorrectedBlks, 
adslAtucChanPerfPrev1DayUncorrectBlks, 
adslAtucChanPerfValidIntervals, 
adslAtucChanPerfInvalidIntervals, 
adslAtucChanIntervalReceivedBlks, 
adslAtucChanIntervalTransmittedBlks, 
adslAtucChanIntervalCorrectedBlks, 
adslAtucChanIntervalUncorrectBlks, 
adslAtucChanIntervalValidData

A collection of objects providing channel block
performance information on an ADSL channel
(ATU-C end) provided by the ATU-R agent.    

Values are:


adslAturChanReceivedBlks, 
adslAturChanTransmittedBlks, 
adslAturChanCorrectedBlks, 
adslAturChanUncorrectBlks, 
adslAturChanPerfValidIntervals, 
adslAturChanPerfInvalidIntervals, 
adslAturChanPerfCurr15MinTimeElapsed, 
adslAturChanPerfCurr15MinReceivedBlks, 
adslAturChanPerfCurr15MinTransmittedBlks, 
adslAturChanPerfCurr15MinCorrectedBlks, 
adslAturChanPerfCurr15MinUncorrectBlks, 
adslAturChanPerfCurr1DayTimeElapsed, 
adslAturChanPerfCurr1DayReceivedBlks, 
adslAturChanPerfCurr1DayTransmittedBlks, 
adslAturChanPerfCurr1DayCorrectedBlks, 
adslAturChanPerfCurr1DayUncorrectBlks, 
adslAturChanPerfPrev1DayMoniSecs, 
adslAturChanPerfPrev1DayReceivedBlks, 
adslAturChanPerfPrev1DayTransmittedBlks, 
adslAturChanPerfPrev1DayCorrectedBlks, 
adslAturChanPerfPrev1DayUncorrectBlks, 
adslAturChanIntervalReceivedBlks, 
adslAturChanIntervalTransmittedBlks, 
adslAturChanIntervalCorrectedBlks, 
adslAturChanIntervalUncorrectBlks, 
adslAturChanIntervalValidData

A collection of objects providing channel block
performance information on an ADSL channel
(ATU-R end) provided by the ATU-R agent.    

Values are:


adslAtucThresh15MinLofs, 
adslAtucThresh15MinLoss, 
adslAtucThresh15MinESs, 
adslAtucThreshFastRateUp, 
adslAtucThreshInterleaveRateUp, 
adslAtucThreshFastRateDown, 
adslAtucThreshInterleaveRateDown, 
adslAtucInitFailureTrapEnable, 
adslAturThresh15MinLofs, 
adslAturThresh15MinLoss, 
adslAturThresh15MinLprs, 
adslAturThresh15MinESs, 
adslAturThreshFastRateUp, 
adslAturThreshInterleaveRateUp, 
adslAturThreshFastRateDown, 
adslAturThreshInterleaveRateDown

A collection of objects providing alarm
provisioning
information about an ADSL Line provided by the
ATU-R agent.    

Values are:


adslLineAlarmConfProfile, 
adslLineAlarmConfProfileRowStatus

A collection of objects providing profile
control for the ADSL system by the ATU-R agent.    

Values are:


adslAtucPerfLofsThreshTrap, 
adslAtucPerfLossThreshTrap, 
adslAtucPerfESsThreshTrap, 
adslAtucRateChangeTrap, 
adslAturPerfLofsThreshTrap, 
adslAturPerfLossThreshTrap, 
adslAturPerfLprsThreshTrap, 
adslAturPerfESsThreshTrap, 
adslAturRateChangeTrap

The collection of ADSL notifications implemented by
the ATU-R agent.    

Values are:


adslAtucChanInterleaveDelay, 
adslAtucChanCurrTxRate, 
adslAtucChanPrevTxRate, 
adslAtucChanCrcBlockLength, 
adslAturChanInterleaveDelay, 
adslAturChanCurrTxRate, 
adslAturChanPrevTxRate, 
adslAturChanCrcBlockLength

A collection of objects providing configuration
information about an ADSL channel.    

Values are:


adslAtucPerfLofs, adslAtucPerfLoss, 
adslAtucPerfLols, adslAtucPerfLprs, 
adslAtucPerfESs, adslAtucPerfInits

A collection of objects providing raw performance
counts on an ADSL Line (ATU-C end).    

Values are:


adslAtucPerfValidIntervals, 
adslAtucPerfInvalidIntervals, 
adslAtucPerfCurr15MinTimeElapsed, 
adslAtucPerfCurr15MinLofs, 
adslAtucPerfCurr15MinLoss, 
adslAtucPerfCurr15MinLols, 
adslAtucPerfCurr15MinLprs, 
adslAtucPerfCurr15MinESs, 
adslAtucPerfCurr15MinInits, 
adslAtucPerfCurr1DayLofs, 
adslAtucPerfCurr1DayLoss, 
adslAtucPerfCurr1DayLols, 
adslAtucPerfCurr1DayLprs, 
adslAtucPerfCurr1DayESs, 
adslAtucPerfCurr1DayInits, 
adslAtucPerfPrev1DayMoniSecs, 
adslAtucPerfPrev1DayLofs, 
adslAtucPerfPrev1DayLoss, 
adslAtucPerfPrev1DayLols, 
adslAtucPerfPrev1DayLprs, 
adslAtucPerfPrev1DayESs, 
adslAtucPerfPrev1DayInits, 
adslAtucIntervalLofs, 
adslAtucIntervalLoss, 
adslAtucIntervalLols, 
adslAtucIntervalLprs, 
adslAtucIntervalESs, 
adslAtucIntervalInits, 
adslAtucIntervalValidData

A collection of objects providing current 15-minute,
1-day; and previous 1-day performance counts on
ADSL Line (ATU-C end) .    

Values are:


adslAturPerfLofs, adslAturPerfLoss, 
adslAturPerfLprs, adslAturPerfESs

A collection of objects providing raw performance
counts on an ADSL Line (ATU-R end).    

Values are:


adslAturPerfValidIntervals, 
adslAturPerfInvalidIntervals, 
adslAturPerfCurr15MinTimeElapsed, 
adslAturPerfCurr15MinLofs, 
adslAturPerfCurr15MinLoss, 
adslAturPerfCurr15MinLprs, 
adslAturPerfCurr15MinESs, 
adslAturPerfCurr1DayTimeElapsed, 
adslAturPerfCurr1DayLofs, 
adslAturPerfCurr1DayLoss, 
adslAturPerfCurr1DayLprs, 
adslAturPerfCurr1DayESs, 
adslAturPerfPrev1DayMoniSecs, 
adslAturPerfPrev1DayLofs, 
adslAturPerfPrev1DayLoss, 
adslAturPerfPrev1DayLprs, 
adslAturPerfPrev1DayESs, 
adslAturIntervalLofs, 
adslAturIntervalLoss, 
adslAturIntervalLprs, 
adslAturIntervalESs, 
adslAturIntervalValidData

A collection of objects providing current 15-minute,
1-day; and previous 1-day performance counts on
ADSL Line (ATU-R end).    

Values are:


adslAtucChanReceivedBlks, 
adslAtucChanTransmittedBlks, 
adslAtucChanCorrectedBlks, 
adslAtucChanUncorrectBlks, 
adslAtucChanPerfValidIntervals, 
adslAtucChanPerfInvalidIntervals, 
adslAtucChanPerfCurr15MinTimeElapsed, 
adslAtucChanPerfCurr15MinReceivedBlks, 
adslAtucChanPerfCurr15MinTransmittedBlks, 
adslAtucChanPerfCurr15MinCorrectedBlks, 
adslAtucChanPerfCurr15MinUncorrectBlks, 
adslAtucChanPerfCurr1DayTimeElapsed, 
adslAtucChanPerfCurr1DayReceivedBlks, 
adslAtucChanPerfCurr1DayTransmittedBlks, 
adslAtucChanPerfCurr1DayCorrectedBlks, 
adslAtucChanPerfCurr1DayUncorrectBlks, 
adslAtucChanPerfPrev1DayMoniSecs, 
adslAtucChanPerfPrev1DayReceivedBlks, 
adslAtucChanPerfPrev1DayTransmittedBlks, 
adslAtucChanPerfPrev1DayCorrectedBlks, 
adslAtucChanPerfPrev1DayUncorrectBlks, 
adslAtucChanIntervalReceivedBlks, 
adslAtucChanIntervalTransmittedBlks, 
adslAtucChanIntervalCorrectedBlks, 
adslAtucChanIntervalUncorrectBlks, 
adslAtucChanIntervalValidData

A collection of objects providing channel block
performance information on an ADSL channel
(ATU-C end).    

Values are:


adslAturChanReceivedBlks, 
adslAturChanTransmittedBlks, 
adslAturChanCorrectedBlks, 
adslAturChanUncorrectBlks, 
adslAturChanPerfValidIntervals, 
adslAturChanPerfInvalidIntervals, 
adslAturChanPerfCurr15MinTimeElapsed, 
adslAturChanPerfCurr15MinReceivedBlks, 
adslAturChanPerfCurr15MinTransmittedBlks, 
adslAturChanPerfCurr15MinCorrectedBlks, 
adslAturChanPerfCurr15MinUncorrectBlks, 
adslAturChanPerfCurr1DayTimeElapsed, 
adslAturChanPerfCurr1DayReceivedBlks, 
adslAturChanPerfCurr1DayTransmittedBlks, 
adslAturChanPerfCurr1DayCorrectedBlks, 
adslAturChanPerfCurr1DayUncorrectBlks, 
adslAturChanPerfPrev1DayMoniSecs, 
adslAturChanPerfPrev1DayReceivedBlks, 
adslAturChanPerfPrev1DayTransmittedBlks, 
adslAturChanPerfPrev1DayCorrectedBlks, 
adslAturChanPerfPrev1DayUncorrectBlks, 
adslAturChanIntervalReceivedBlks, 
adslAturChanIntervalTransmittedBlks, 
adslAturChanIntervalCorrectedBlks, 
adslAturChanIntervalUncorrectBlks, 
adslAturChanIntervalValidData

A collection of objects providing channel block
performance information on an ADSL channel
(ATU-C end).    

The compliance statement for SNMP entities
which manage ADSL ATU-C interfaces.    

The compliance statement for SNMP entities
which manage ADSL ATU-R interfaces.